Posted on

How to Make… Luxurious Laser Cut Invitations

DIY wedding invitation. Luxury DIY wedding stationery supplies. Make your own wedding stationery. Blank laser cut invitatons

How To Make ……. Luxurious Laser Cut Invitations

I cannot even begin to tell you how much I love designing with Laser Cut. With a minimum amount of effort, you can create really striking Luxurious Laser Cut Invitations that your friends will be more than impressed with.

This design can be easily customised but just changing the colours of the invitation, card or ribbon.

If you can tie a bow, you can make this invitation easily.

 

 

DIY wedding invitation. Luxury DIY wedding stationery supplies. Make your own wedding stationery. Blank laser cut invitatons

HERE’S WHAT YOU’LL NEED:

 

You Will Need: 

cream laser cut invitation. Blank laser cut wedding invitation in cream. DIY wedding stationery supplies

1 x Jaipur Cream Invitation

BUY
A4 Card Bisque Sparkle, a4 glitter card in mink. Bisque lustre a4 card

1 Sheet of A4 Card in Bisque Sparkle

 

BUY
Pearlised cream A4 Card. DIY wedding stationery card making and crafts

1/4 x Pearlised Cream Card

 

BUY
38mm Dusky Pink Satin Ribbon , Wide satin ribbon on Dusky pink. 35mm double faced satin ribbon. Roll of wide ribbon for DIY wedding stationery

Appx. 35cm of 38mm Dusky Pink Ribbon

 

BUY
Roll of satin ribbon in Dusky Pink. 25mm wide. DIY wedding stationery supplies

Appx. 35cm of 19mm Dusky Pink Ribbon

 

 

BUY

 

Other Things You Might Need:

Tools_270x250 Paper Trimmer BUY
Useful_270x250 Tape Runner or Double Sided Tape BUY
Useful_270x250

Glue Gun

BUY

 

Luxury DIY wedding invitation to make yourself. DIY wedding invitation. Blank laser cut wedding stationery

INSTRUCTIONS:

Here’s How You Do It:

Inside:

  1. Print your wording on to the Bisque Sparkle Card and cut down to size. The finished size should be appx. 10cm x 10cm. If you print the wording at the top of the sheet, you will have enough left over card to cut the backing sheet.
  2. From the remaining Bisque Sparkle card, cut a panel 14.5cm x 14.5cm. Use your double sided tape to stick this to the inside panel of your laser cut invitation.
  3. Cut a piece of pearlised cream card 10.5cm x 10.5cm. Stick this on top of the Bisque Sparkle Card making sure that all the borders are even.
  4. Stick your invitation wording on top.

 

Front:

  1. Fold your invitation closed.
  2. Place your 19mm ribbon on a flat surface. Put your invitation on top making sure that it is in the centre of the ribbon. Fold both ends of the ribbon in to the front of the card. Use a small amount of glue from the glue gun to secure one end of the ribbon to the other. Make sure that you do not spill any glue on to the laser cut card.
    When you do this, you will need to make sure that you do not pull too tight (you should be able to slide the ribbon over the top of the card). However, you also need to make sure that you do not make it too loose so that it falls off easily.
  3. Tie a bow with the 38mm ribbon (I like to use the bunny ears method). Keep pulling and tightening your bow until it’s nice and near. Use a scissors to evenly trim the excess ribbon into inverted “v” shapes.
  4. Once you are happy with your bow, you can use your glue gun to stick it on to the front of the 19mm ribbon. Try to make sure that you cover the join in the ribbon when you glue it in to place.   Be careful not to spill any glue on to the card.
  5. And you’re done!

DIY wedding invitation. Luxury DIY wedding stationery supplies. Make your own wedding stationery. Blank laser cut invitatons

Why not customise your other stationery to match with these new pop out laser cuts:

Look at our Jaipur ranges available in other colours too: